I am trying to make an ACE 2 rig but due too creeping age and financial  restraints I am slower than I would like to be. I think there is light at the end of the tunnel so I will persist. Are there any members in Australia going down this path? Regards dave

Views: 315

Reply to This

Replies to This Discussion



Martin Moore said:

Hey... Thanks for the vote Marc. :)

David... anything I can help you with just ask. I spent a couple of hours chatting to Howard yesterday and we are still talking about that little H-Bridge piece of kit.

marc tamiso said:

Good day Dave, you are on to a good thing, keep at it.  My first ACE cells were cast ( sash weight and pipe) and drew high amps, but changed to aluminum  and sodium citrate and got great results.  Martin's PWM design makes it even simpler and more efficient.  Please keep us posted

Hi Martin I would like to take up your offer about H Bridge piece of kit  Regards   Dave

David Brightman said:



Martin Moore said:

Hey... Thanks for the vote Marc. :)

David... anything I can help you with just ask. I spent a couple of hours chatting to Howard yesterday and we are still talking about that little H-Bridge piece of kit.

marc tamiso said:

Good day Dave, you are on to a good thing, keep at it.  My first ACE cells were cast ( sash weight and pipe) and drew high amps, but changed to aluminum  and sodium citrate and got great results.  Martin's PWM design makes it even simpler and more efficient.  Please keep us posted

Hi Dave,

I've been away in Ireland for a couple of weeks.

Anyway... I've attached my original work for you on the H-Bridge driver for Howard's ACE cell.

ACE2%20H-Bridge%20Driver.pdf

All of the parts are available on EBay.

Regards

Martin

Martin, Shane Brightman here, son of Dave. I have been tasked with assembling the unit for my old man, and have a few questions. In Step 3 of the PDF there is a connection from the LM358 module OUT to pin 1 on the H Bridge, and from the transistor side of the 1k resistor on the VCC line to pi 2 on the H Bridge.

Now, Step 4 has me a little confused. If I am reading it right, the LM358 connects from VCC to pin 7 and GND to pin 8. Also, the Buck Power Module + out to pin 7, and - out to pin 8.

If this is correct, I can proceed, and hand the module off to Dave.

Thanking You.

Reply to Discussion

RSS

*** Translate HODINFO ***

Latest Activity

richard r may is attending Ed Grimm's event

Ed Grimm at Clearwater, Florida

March 22, 2019 at 12pm to March 24, 2019 at 8pm
2 hours ago
Bradley Glen posted a discussion
3 hours ago
Bradley Glen replied to Bradley Glen's discussion 'Potassium Hydroxide - what is next best while I wait for KOH supply'
4 hours ago
Greg Kusiak replied to Bradley Glen's discussion 'Potassium Hydroxide - what is next best while I wait for KOH supply'
5 hours ago
Ed Grimm and Glenn P DeRosa are now friends
Feb 10
Allan Wells left a comment for Shane Brightman
Feb 9
Dave Brightman replied to gabet123's discussion 'Hydrogen gas trial in western Sydney could unlock $1.7bn in renewable exports'
Feb 8
moldoveanu.marius and Ed Grimm are now friends
Feb 6
moldoveanu.marius favorited Ed Grimm's event Ed Grimm
Feb 6
moldoveanu.marius favorited Ed Grimm's event Ed Grimm
Feb 6
moldoveanu.marius favorited Ed Grimm's event Ed Grimm
Feb 6
Barry Holzsweig commented on Ed Grimm's event 'Ed Grimm'
Feb 4
Barry Holzsweig is attending Ed Grimm's event

Ed Grimm at Clearwater, Florida

March 22, 2019 at 12pm to March 24, 2019 at 8pm
Feb 4
eric keogh left a comment for Ed Grimm
Feb 3
gabet123 might attend Ed Grimm's event

Ed Grimm at Clearwater, Florida

March 22, 2019 at 12pm to March 24, 2019 at 8pm
Feb 3
Profile Iconmajid toosi and Dave Brightman joined HODINFO
Feb 3

© 2019   Created by gabet123.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

Live Chat