HODINFO is a collaborative think tank/ open science initiative. We are an International group comprised of inventors, scientist, mechanics, tinkerers, fabricators, and out of the box thinkers. Our mission is to find innovative solutions to the problems that primarily limit the production and delivery of H2. As the world starts using hydrogen it becomes clear that immense infrastructure initiatives will be required to make it happen. If adequate solutions can be found to support Hydrogen-On-Demand (HOD) systems then the world can remove great and costly limitations on future applications. The future is not just Hydrogen, it's Hydrogen-on-Demand.


I've made a lot of brainstorming about HHO circuit to improve efficiency reliability and ease of tuning. 

This is what I came up with. 

This is basicaly a DC circuit, with a higher voltage, around 120V, high frequency pulse from a custom made flyback transformer. 

It is somewhat similar to what Bob Boyce 100 plate design, it has a strong DC bias with a high frequency pulse riding on top.. Except he was using 3 frequencies, I'll be using just one. Also, my circuit uses a separate circuit to create the HF as he was pulsing on the same transformer.  This allow me to create a higher voltage pulse. Current from the DC side will be controller via:

*the number of turns on the chokes

*electrolyte concentration

*Pulse width and freq of the PWM: controls the amount of current that goes into the secondary, thus creating more or less ionisation of the water, that define the amount of current that'll flow from the DC side. I may have to add a voltage control (DC/DC circuit) before the PWM, to have more precise control of current.

Also, not drawn, is a diode on the + side, between cell and battery, to keep the HF pulse going back to the battery. Obviously, I've ommited to draw the relay, breaker and fuse piggy back that goes on the vehicle.

I didn't draw the diode cause I wanted to know what you guys think, if it'll be necessary or not. 

The cell is a 13 plates, 5 neutral, with a quarter inch gap. It's a wet cell, all plates are joint at the bottom of the cell, with an epoxy or urethane casting. So they are all free to vibrate, in as overhang fashion. 

It'll allow for acoustic, mechanical and possibly L/C resonances. 

Please tell me what are your thoughts about it.

Thank you. 

Views: 6


Reply to This

*** Translate HODINFO ***

Latest Activity

Felix Audet posted a discussion
Mar 11
charles ware posted a discussion
Mar 10
Glenn P DeRosa shared Stuart Kinley's group on Facebook
Mar 9
Felix Audet posted a discussion
Mar 3
Felix Audet replied to Felix Audet's discussion 'HV + DC electrolysis'
Feb 24
Felix Audet replied to Felix Audet's discussion 'HV + DC electrolysis'
Feb 18
David Brightman posted a status
"Currently getting set to build an ACE2 type cell.I could not find any cast iron pipe here so I found some cast iron sash weights I will"
Feb 6
David Brightman favorited gabet123's discussion Howard Phillips Ace Cell
Feb 5
Macel is now a member of HODINFO
Feb 4
Barry Holzsweig replied to Joseph Tasso's discussion 'HHO sensor?'
Feb 2
broandrew replied to Joseph Tasso's discussion 'HHO sensor?'
Feb 2
Mickey Hudson is now a member of HODINFO
Feb 2
moldoveanu.marius left a comment for gabet123
Jan 31
moldoveanu.marius posted a status
"Engine and exhaust circuit cleaning by atomized water based additives solution"
Jan 31
rodolfo berio is now a member of HODINFO
Jan 17
Barry Holzsweig posted a status
"We now have Volo EFIEs that plug into the OBD port. No wire taps necessary. Check out the pics."
Jan 14

© 2018   Created by gabet123.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

Live Chat