MEMBER SPECIAL $19.99 Until October 31, 2012

The Original "How We Did It"

Fully Automatic HHO Heater Documentary

On A New Special HHOINFO Edition DVD

Included with DVD

* Our Original Step By Step Documentary showing each step of our build.

* Free online membership to hhoheaterplans.com with free Online Updates.

* Parts List - Parts used in the build of our Fully Automatic HHO Heater.

Here is a list of the almost 2 hours of steps we have on this one DVD

Step 1    - This Video Shows you the smoker unit we purchased to house all of the components of the HHO heater.
Step 2    - Explaining the second bubbler  This was for looks only and you can use what ever you wish for your second bubbler.
Step 3    - Themaltake fan.
Step 4    - Installing the Shurflo diaphram pump into the cabinet.
Step 5    - Installing HHO cell.
Step 6    - Installing the 120-24v transformer into the cabinet.
Step 7    - Installing the 24v coil DP/DT relay, secondary relay installation.
Step 8    - Installing 24v coil DP/DT relay, primary realy installation.
Step 9    - Instalation of the ICM Delay on make timer.
Step 10  - Installing the Ground Bar.
Step 11  - Installing the 12v terminal block.
Step 12  - Installing the 24v up to temp relay.
Step 13  - Installing the 12v DC. Power Supply.
Step 14  - Installing the main power plug.
Step 15  - Installing the Thermaltake glycol pump into the cabinet.
Step 16  - Installing a main 4 square electrical switch box with a 12v amp guage installed.
Step 17  - Wire installation from the main socket to switch box and from 12v power supply to main switch box.
Step 18  - Installing the 120v wires for the 120-24v transformer, from transformer to main switch box.
Step 19  - Installing the 120v hot and neutral wire from the main switch box to the dimmer to feed the Shurflow pump.
Step 20  - Installing the dimmer switch for the pump. Neutral wires.
Step 21  - Explanation of the dimmer switch.
Step 22  - Ground wire instalanation from dimmer and pump to terminal block.
Step 23  - Main switch box, explanation of neutral wires.
Step 24  - Crimp ends on black and red wires. More wiring information.
Step 25  - Main switch box, terminating black, 120v wires from pump dimmer switch and 12v power supply red wire from primary relay.
Step 26  - Main switch box, installing standard light switch.
Step 27  - 12v power supply wiring.
Step 28  - Connecting neg. from power supply to neg. on cell.
Step 29  - Explanation of moving from wiring to now installing some plumbing.
Step 30  - Explanation of the first bubbler.
Step 31  - Installation of hose to tank, mounting of tank.
Step 32  - Installation of hose from top barb fitting on second bubbler.
Step 33  - Installation and explanation of the glycol hoses.
Step 34  - Tubing coil installation, tube coil installed in 4" pipe and mounted in top of cabinet.
Step 35  - Installation of hoses to tube coil, front hose on tube coil to outlet side of pump, back hose on tube coil to bottom of cell.
Step 36  - Explanation of cap on second bubbler, flashback arrestor and solenoid valve hose from cap to flashback to solenoid.
Step 37  - Installation of cap on second bubbler, flashback arrestor and solenoid valve.
Step 38  - Explanation of 1/4" copper from solenoid valve to torch.
Step 39  - Explanation of LED's.
Step 40  - 12v DC wires from power supply.
Step 41  - 12v DC wires from power supply, yellow wire 12v pos.
Step 42  - Explanation of ground wires on LED's.
Step 43  - Wiring up to temp LED.
Step 44  - Wiring strip LED's on the sides of the second bubbler
Step 45  - Wiring low water level LED.
Step 46  - Wiring glycol pump.
Step 47  - Explanation of the heat exchanger.
Step 48  - Mounting thermal disc snap switch on other side of the heat exchanger.
Step 49  - Adjusting snap switch on back side of the heat exchanger.
Step 50  - Explanation of glycol block separate of heat exchanger and 1/8" x 3/8" barb fitting, install heat exchanger.
Step 51  - Torch assy, .030 mig tip flattened to make the hole smaller, torch designed to fit our system.
Step 52  - Installation of torch assembly.
Step 53  - Clamp installation on torch assembly.
Step 54  - Explanation of brackets for heat exchanger.
Step 55  - Install to heat exchanger, install heat exchanger with bracket in system centering torch tip with center of heat exchanger.
Step 56  - Installation of u bolt to torch assembly.
Step 57  - Installation of sparker.
Step 58  - Installation of glycol lines to water block.
Step 59  - Installation of spark box.
Step 60  - Wire from sparker connected to top terminal on spark box
Step 61  - Wiring other side of front snap switch.
Step 62  - Wiring spark box, orange wire with spade terminal on each end.
Step 63  - Wiring spark box, blue wire to connect to left side of spark box.
Step 64  - Wiring spark box - Cont.
Step 65  - Explanation of t-stat, long probe to sense temp, installing bracket in front of sparker.
Step 66  - Wiring t-stat.
Step 67  - Wiring t-stat. - Cont.
Step 68  - Wiring t-stat. - Cont.
Step 69  - Wiring t-stat. - Cont.
Step 70  - Wiring t-stat. - Cont.
Step 71  - Wiring transformer.
Step 72  - Wiring time delay.
Step 73  - Wiring secondary relay.
Step 74  - Wiring secondary and up to temp relay.
Step 75  - Wiring secondary. relay, white wire from top right on secondary relay to snap switch on back side of the heat exchanger.
Step 76  - Wiring snap switch, 2nd terminal on back snap switch to bottom right terminal of primary relay.
Step 77  - Wiring solenoid valve.
Step 78  - Wiring to secondary and primary relay
Step 79  - Drain assy.
Step 80  - Explanation of drain.
Step 81  - Explanation of filling the second bubbler.
Step 82  - Installing cap on second bubbler. and explaining the water level
Step 83  - Mixing electrolyte.
Step 84  - Adding electrolyte to the first bubbler.
Step 85  - Tightening cap. make sure tight...
Step 86  - Filling glycol pump with distilled water.
Step 87  - Purging the air from the system.
Step 88  - Final check on all electrical components... also check all plumbing.
Step 89  - Purging the air from all of the plumbing.
Step 90  - Cycle system 2-3 times to purge all air from water lines.
Step 91  - Check all fittings,connections and check for any water leaks and fix.
Step 92  - Starting system, leak test lines with soapy water, turn t-stat on, bleed air from gas lines.
Step 93  - Adding more electrolyte to raise amp rate, starting system.
Step 94  - One hour run time, explanation of system running.

Here is step 48 of the 94 videos included in the DVD

The Sale Of Our DVD Helps Support The Growth Of This Technology

Coming Soon!!!

New Lab

All New Data Logging Software

A New Build

Live Online Classes

Cell Testing

Make sure to Join our blog here at HHOINFO to get

updates on future Online Classes.

(HHO Heater Group)

Live Shows Coming Soon - See the USTREAM Button On Your Right------>

* Our Original Step By Step Documentary showing each step of our build.

* Free online membership to hhoheaterplans.com with free Online Updates.

* Parts List - Parts used in the build of out Fully Automatic HHO Heater.

* Discounts of up to 50% off on any future online classes.

(For HHOINFO members who own this DVD).

Get All Of This For Just

JUST $19.99 Until Oct. 31, 2012

Only Here at HODINFO

Save $30.00

Buy With Paypal Click Here

Buy With Credit Card Click Here

 Normally we offer proceeds of sales to those that sell our DVD.

HHOINFO has declined any profits as long as we roll these profits into discounts for future services we will be offering to HHOINFO members and to help further this project.