HODINFO is a collaborative think tank. We are an International group comprised of inventors, scientist, mechanics, tinkerers, fabricators, and out of the box thinkers. Our mission is to find innovative solutions to the problems that primarily limit the production and delivery of H2. As the world wakes up to the idea of using hydrogen it also becomes clear that immense infrastructure initiatives will be required to make it happen. If adequate solutions can be found to support HOD systems then the world can remove great and costly limitations on future applications. It is important to realize that the future is not just Hydrogen, it's Hydrogen-on-Demand.

Felix Audet
  • Quebec
  • Canada
Share

Felix Audet's Friends

  • moldoveanu.marius

Felix Audet's Discussions

Corrosion and Circulating HHO cells

Started Mar 12 0 Replies

I've done a lot of testing in the last 2 years, with a tubular cell, starting with a tube pair, then 3 tubes, on 12V and I've always ended up with corrosion and brown water after a few months. I was…Continue

Tags: cell, HHO, Circulating

Custom Gasket cutting

Started this discussion. Last reply by Jesse Wilson Nov 16, 2016. 3 Replies

I'm looking for a CUSTOM GASKET CUTTER, for small batches and fairly cheap.. Any advice? Also, i've found that strong NaOH solution tend to affect rubber gaskets.. Verry strong smell close to the…Continue

Using Peroxide ( H2O2) as anti-freeze agent

Started this discussion. Last reply by Felix Audet Mar 12. 2 Replies

Another Idea that I had in mind.. winter is comming here in Canada.. this usually mean the end of season for HHO boosting.. Unless you have heater and a place where you can always plug in.. There are…Continue

Resonnance electrolysis VS HV flyback

Started this discussion. Last reply by gabet123 Oct 12, 2016. 1 Reply

It's been a while since I've heard about resonnance is key to more than 100% efficiency, but I've never seen a HHO setup that uses resonnance, never on youtube, much less one for sale..With today's…Continue

 

Felix Audet's Page

Latest Activity

gabet123 replied to Felix Audet's discussion 'Using Peroxide ( H2O2) as anti-freeze agent'
"You could just create a thermostatically controlled water pump to drain the cell if it is about to freeze."
Dec 29, 2016
Jesse Wilson replied to Felix Audet's discussion 'Custom Gasket cutting'
Nov 16, 2016
Leslie Gurvey replied to Felix Audet's discussion 'Custom Gasket cutting'
"Fairly cheap will get you into a lot of trouble when the system fails.So don't be penny wise and dollar stupid. As for NaOH, that is your first mistake in any HHO system. It is too corrosive and will destroy the system in a short time. A less…"
Nov 15, 2016
gabet123 replied to Felix Audet's discussion 'Custom Gasket cutting'
"Check these guys out http://www.gasketstogo.com/"
Nov 9, 2016
Felix Audet posted discussions
Nov 8, 2016
gabet123 replied to Felix Audet's discussion 'Resonnance electrolysis VS HV flyback'
"Square 1 Energy, LLC I know has gotten very close. Check out this device http://freeenergynews.com/Directory/Hydroxy/Hydro-Maxx/Controller%20Announcement-2%20with%20pic.pdf They mention a little about it…"
Oct 12, 2016
Felix Audet posted a discussion

Resonnance electrolysis VS HV flyback

It's been a while since I've heard about resonnance is key to more than 100% efficiency, but I've never seen a HHO setup that uses resonnance, never on youtube, much less one for sale..With today's arduino and cheap yet powerful electronic components, it seems it would be fairly easy and cheap to set up such a system..From what I understand, at resonnance, the cell naturally wants to create high voltage..  so you get it free as a by product of resonnance?  it it the case?Cell will have a point…See More
Oct 5, 2016
Felix Audet replied to Bill Nash's discussion 'HHO systems working with modern day engines (ECUs)'
"There are several ways to reduce engine temps due to lean mixtures.  In a document from the 70's made by Ford company, about testing on HHO boost on gasoline and diesels, they said the best way to do that was to inject water, water vapour,…"
Oct 2, 2016
Felix Audet replied to Bill Nash's discussion 'HHO systems working with modern day engines (ECUs)'
"Also, one thing that can help is to add water vapour to the air/ fuel / hho mixture..  It will trick the ECU into thinking the mixture is too rich..  That may be the simplest method of all..  Side to side with the plug & play…"
Oct 1, 2016
Felix Audet replied to Bill Nash's discussion 'HHO systems working with modern day engines (ECUs)'
"I have a pro tuner installed on a 95 honda, working great if you want to cut the fuel up to around 20% leaner..  That's about the most the ECU will let you lean with only tricking the sensors.  To go leaner that that, you can A,…"
Sep 30, 2016
Felix Audet replied to Spodie Odie's discussion 'Painless High Power High Speed Switching (PWM)'
"Actually I'm using the PWM set I already have installed. It's a Kelly motor controller that operate at 16.6 kHz and can handle up to 60A continuous. My alternator can't go pass 20A continuous for a long period without…"
Sep 3, 2016
Felix Audet replied to Spodie Odie's discussion 'Painless High Power High Speed Switching (PWM)'
"230 V DC without neutral plates!   You bet you must be burning your stuff :) But hey, running without fuel is quite an achievement.. even for a short while.. I the ionisation of the gas is what allowed you to run fuelless with only one litter…"
Sep 3, 2016
Felix Audet replied to Spodie Odie's discussion 'Painless High Power High Speed Switching (PWM)'
"** I meant retard timing.. "
Sep 3, 2016
Felix Audet replied to Spodie Odie's discussion 'Painless High Power High Speed Switching (PWM)'
"One liter per minute to run a 460 Ci Wow!  Never heard of that..  How many 12 x 12 and how many neutrals were you using? KOH + distilled water?  at what concentration?   I'm assuming you were running from the stock…"
Sep 3, 2016
Felix Audet replied to Spodie Odie's discussion 'Painless High Power High Speed Switching (PWM)'
"You mean your cell melted because of too much current?  How much current? How many LPM to run the truck? How did you advance timing to after TDC? Can you provide details about the setup? Thanks."
Sep 2, 2016
gabet123 replied to Felix Audet's discussion 'FlashBack Arestor and cell under vacuum'
"You could always add polymer crystals to a bubbler. Get the ones that are round like marbles. Just make sure they can't get sucked out. They will absorb a lot of water but still act as water does in a bubbler. This might give you more time…"
Apr 15, 2015

Profile Information

What is your HOD level of experience?
Intermediate Builder
Do you have a website about HOD technology? Please link to HODINFO also!
http://felaudet.wix.com/open-source-100mpg
What do you do for a living or have special education in?
Mechanical Engineering

Comment Wall (1 comment)

You need to be a member of HODINFO to add comments!

Join HODINFO

At 6:23pm on October 6, 2014, gabet123 said…

FYI Two of the videos on your site are dead links.

 
 
 

*** Translate HODINFO ***

Archive this page

Latest Activity

Roy posted a status
"Tesla a leader on free energy. For those that have time to read here's a link. http://fuel-efficient-vehicles.org/energy-news/?page_id=785"
Apr 14
broandrew commented on gabet123's group 'HHO TORCH GROUP'
Apr 11
broandrew joined gabet123's group
Apr 11
charles ware replied to charles ware's discussion 'Measurements of temperature and electron density of oxyhydrogen (HHO) flame'
Mar 29
soohaeng hong is now a member of HODINFO
Mar 21
soohaeng hong favorited Randy Bunn's discussion We have developed a home heating unit!
Mar 21
Andrew Batty shared their discussion on Twitter
Mar 17
Andrew Batty posted a discussion
Mar 17
Andrew Batty replied to Andrew Batty's discussion 'Hydrogen for Health'
Mar 17
Slobodan Stankovic replied to charles ware's discussion 'Measurements of temperature and electron density of oxyhydrogen (HHO) flame'
Mar 16
Slobodan Stankovic updated their profile
Mar 16
gabet123 posted a discussion
Mar 15
Jeremy Dukes posted a status
"FREE Installation of any reputable hho kit on Sundays in San Diego. Call me anytime 6194087854"
Mar 14
gabet123 left a comment for Anthony Preston
Mar 1
Anthony Preston posted a discussion
Feb 28
Anthony Preston commented on gabet123's page 'FUNDING'
Feb 28

© 2017   Created by gabet123.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

Live Chat
Warning: require_once(xn-app://widgetlaboratory/apps/windex.php): failed to open stream: "XN_AppFilesystemStream::stream_open" call failed in /apps/hhoinfo/index.php on line 5 Fatal error: require_once(): Failed opening required 'xn-app://widgetlaboratory/apps/windex.php' (include_path='.:/php/includes/XN:/php/includes/PEAR:/php/includes/other') in /apps/hhoinfo/index.php on line 5