HODINFO is a collaborative think tank/ open science initiative. We are an International group comprised of inventors, scientist, mechanics, tinkerers, fabricators, and out of the box thinkers. Our mission is to find innovative solutions to the problems that primarily limit the production and delivery of H2. As the world starts using hydrogen it becomes clear that immense infrastructure initiatives will be required to make it happen. If adequate solutions can be found to support Hydrogen-On-Demand (HOD) systems then the world can remove great and costly limitations on future applications. The future is not just Hydrogen, it's Hydrogen-on-Demand.

Jason Albrecht
  • Male
  • Naracoorte South Australia
  • Australia
Share

Jason Albrecht's Friends

  • Hans Peter GROTE
  • Mark Hansen
  • Barry Holzsweig
  • Aquapulser
  • ROSS GRANBY
  • armirani betona
  • B.Williams
  • Ben
  • Bruce T. Gardner
  • Chris Atkinson
  • Shane Liew
  • Dan DeShon
  • julian mayston
  • D Richardson
  • Zdahn

Jason Albrecht's Discussions

CAT12 2004 truck engine

Started this discussion. Last reply by Barry Holzsweig Dec 19, 2011. 12 Replies

HHO Gas when towing heavy loads

Started this discussion. Last reply by stuart glenister Aug 28, 2013. 11 Replies

 

Jason Albrecht's Page

Profile Information

What is your HOD level of experience?
Intermediate Builder
What is your Skype ID? Skype it is free and recommended. http://skype.com
no skype as yet
Is there anything else you would like to add?
email rawhydroaustralia@gmail.com

Comment Wall (21 comments)

You need to be a member of HODINFO to add comments!

Join HODINFO

At 11:38am on November 12, 2011, Unca RaF said…

Greetings,

   My name is Ralph Gugar from "North Coast Flow Testing Lab", and I'm also one of the founding members of the "International HHO Institute" (IHHOI). It has been brought to my attention through HHOINFO that you may have interest in having an HHO cell, flow tested. I'm sorry that someone from the IHHOI has not contacted previously, but there must be a glitch in the system from when someone requests info by clicking on the IHHOI link on HHOINFO.

   Please feel free to go directly to the IHHOI website at: "IHHOI.org" and you can learn exactly what the IHHOI is all about, from becoming a member, to HHO cell testing and how to place an order for a cell test, and to their vision of what they plan to accomplish:

  • To be the premier authority and open source of information for the
    discovery, development, and advancement of sustainable, renewable energy
    sources.
  • To promote HHO as a viable, sustainable, alternative energy.
  • To help reduce our dependence on foreign and domestic oil companies and our
    dependence on polluting, petroleum based-fossil fuels.
  • To provide standards for Quality, Safety, Installation, and Integrity
    solutions to meet the needs of its members.
  • Further, with the goal of becoming recognized as the “UL” for the HHO
    industry providing product registration and product performance certification.
At 11:45am on October 3, 2011, Mark Hansen said…

I have not been given any specifics about who builds the PWM that I use, however you can find it @ http://www.dry-cells.com/components/constant-current-pwm-with-lcd-controller.

 

It's a great controller.

 

What is your price on your controller?

At 10:40am on September 30, 2011, Mark Hansen said…

Hello Jason

Yes, I do use a pwm but I'm always anxious to see what else is out there.  Please send me spec's and other information you have about your pwm.

 

thanks 

Mark

At 8:38am on June 13, 2011, Allan Wells said…

Thanks again Jason,  I have added a mini inline moisture trap between the dryier and the air intake. I had thought that a bubbler would take out any nasty impurities before the hho went into the air intake. The said bubbler, was below the reservior. Regarding less hho in diesil's, I have found similar results to those indicated. Also, I am having the problem of any gains made in economy being reversed shortly afterwards, as reported by someone else recently.

 

Night

At 4:16am on June 13, 2011, Grasack said…

Hi Jason

Thanks for the invite I am trying to get results with My Pajero diesel using HHO. Seems the electronics are agaist me.

Am trying Dans formula and it appears not to be working. Will keep going on this.

Also am building GSC cell similar to Bill Williams design. On third rebuild due to membrane problems. Think I have it Licked this time, time will tell.

What sort of cells are you working with ??

Cheers

At 11:37pm on June 12, 2011, Allan Wells said…

Thanks Jason, Regarding bubbler, 50mm pipe with end caps around 180mm in length, hho entered the side of the bubbler near the bottom and left the side of the bubbler near the top (had about 2/3's full of water). The bubbler was installed so that the hho gas went through the bubbler after it had passed through a drier situated at the top of the resivior. I have a temperature sender at the bottom of the resivior and the system opporates at 20 - 30 Deg' C (gets a bit warmer when standing still). All tubes are less than a meter in length.

Cheers. 

 

At 9:54pm on December 28, 2010, Ben said…
Hi Jason,

I just left a message on the diesel forum regarding leaning out the fuel. How can one tell when the leaning out has gone to far?. Any thoughts please?

Just for any others here that have not gone to the diesel forum, I have built an interceptor that goes between the MAP and the ECU that allows me to re map the fuel to either lean it out or enrich it. It allows 128 load points and 127 minor adjustments to the mixer at each load point.
At 4:08am on November 24, 2010, armirani betona said…
of course, I love pandas ;)
At 5:35pm on November 20, 2010, Lance Bennett said…
Jason,
Sorry for the late reply. I got my HALO plugs from the U.S.A. Go to www.haloplug.com .
At 1:13am on July 5, 2010, Chris Atkinson said…
Hey Jason Chris Atkinson Here , Ive a jar HHO system , built by a Older Man in Wainuiomata , near lowerhutt , Wellington NZ , I just ordered a Flash chip from water4gas , I had no luck with the effie style O2 sensor attachment , I guess My car was too new , 2000 nissan avenir , I have a port to plug into an Ob11 port , so wish me luck , what are you up to ????
 
 
 

*** Translate HODINFO ***

Latest Activity

Felix Audet replied to Felix Audet's discussion 'HV + DC electrolysis'
Monday
David Brightman posted a status
"Currently getting set to build an ACE2 type cell.I could not find any cast iron pipe here so I found some cast iron sash weights I will"
Feb 6
David Brightman favorited gabet123's discussion Howard Phillips Ace Cell
Feb 5
Macel is now a member of HODINFO
Feb 4
Barry Holzsweig replied to Joseph Tasso's discussion 'HHO sensor?'
Feb 2
broandrew replied to Joseph Tasso's discussion 'HHO sensor?'
Feb 2
Mickey Hudson is now a member of HODINFO
Feb 2
moldoveanu.marius left a comment for gabet123
Jan 31
moldoveanu.marius posted a status
"Engine and exhaust circuit cleaning by atomized water based additives solution"
Jan 31
rodolfo berio is now a member of HODINFO
Jan 17
Barry Holzsweig posted a status
"We now have Volo EFIEs that plug into the OBD port. No wire taps necessary. Check out the pics."
Jan 14
shiyong is now a member of HODINFO
Jan 3
Jessee McBroom favorited gabet123's discussion Catalytic Carbon PR11 Press Release new concepts and ACE cell.
Jan 2
moldoveanu.marius replied to Felix Audet's discussion 'HV + DC electrolysis'
Jan 2
Barry Holzsweig replied to Felix Audet's discussion 'HV + DC electrolysis'
Jan 2
Jessee McBroom replied to gabet123's discussion 'Catalytic Carbon PR11 Press Release new concepts and ACE cell.'
Jan 2

© 2018   Created by gabet123.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

Live Chat