John
  • Male
  • Roaring Gap, NC
  • United States
Share
 

John's Page

Latest Activity

John replied to Spodie Odie's discussion 'Painless High Power High Speed Switching (PWM)'
"Have you done any test on the water formula you plain to use to find it's breakdown point to know where to start with from your pwm"
Sep 3, 2016
John replied to Spodie Odie's discussion 'Painless High Power High Speed Switching (PWM)'
"The best I remember there where about sixty plates half and half. The power from the hydrogen was more than enough to run smoothly. And the fast burn of it makes it work I ran the hours from the unit I had built a generator with a thirteen hours…"
Sep 3, 2016
John replied to Spodie Odie's discussion 'Painless High Power High Speed Switching (PWM)'
"I think it was 43amp and the heat generated from the cell melted the pvc components I had used 1 1/4" Lexan and that warped as well. It was a 1997 f250 460 Cid so all I had to do was move the distributer to two degrees after tdc . I had figured…"
Sep 2, 2016
John replied to Spodie Odie's discussion 'Painless High Power High Speed Switching (PWM)'
"i drove for two miles before i melted .pure hho . that's correct no gas at all and the truck ran smother without it yes i even checked the exhaust out the tail pipe and if it had never been run on gas you could breath it but with my face in the…"
Sep 2, 2016
John replied to Spodie Odie's discussion 'Painless High Power High Speed Switching (PWM)'
Aug 31, 2016
John replied to alexis ballesteros's discussion 'Choke coils'
"remember in a coil E leads I and a capacitor I leads E . and the  I was at min EMF was to be suffance you over come  the electron to cause release attraction to one potential and the o to the other. if i remember right."
Jan 30, 2015
John replied to don's discussion 'ha what about a intake heater'
"I would keep the heater on to maintain the gaseous state of the fuel ."
Jan 28, 2015
John commented on Hans Peter GROTE's group 'The DRY-CELL Hydrogen Generator Builders Group'
"The only testing I have done is with 99.9 pure hydrogen.I have driven my f250460cid two and one half miles no gasoline ."
Feb 25, 2012
gabet123 left a comment for John
"Your interaction number 2"
Jan 4, 2012
John commented on gabet123's group 'Circuitry Design Group'
"Try an igbt instead of straight mosfet"
Dec 14, 2011
John replied to James Morehead's discussion 'Mosfet driver' in the group Circuitry Design Group
"Try n I g b t instead of a straight mosfet"
Dec 14, 2011
John joined gabet123's group
Dec 14, 2011
John commented on Hans Peter GROTE's group 'The DRY-CELL Hydrogen Generator Builders Group'
"thanks got it"
Dec 8, 2011
John commented on Hans Peter GROTE's group 'The DRY-CELL Hydrogen Generator Builders Group'
"Does anyone know how to figure the capacitance of a dry cell"
Dec 8, 2011
John joined Hans Peter GROTE's group
Thumbnail

The DRY-CELL Hydrogen Generator Builders Group

We like to exchange Information about building and Design of Dry-Cell Hydrogen Generators.
Dec 8, 2011
John favorited David Bixler's discussion Stan Meyer's circuit schematics and vic measurments! What you have been waiting for!! must have!!!
Nov 14, 2011

Profile Information

What is your HOD level of experience?
Intermediate Builder

Comment Wall (2 comments)

You need to be a member of HODINFO to add comments!

Join HODINFO

At 10:03am on January 4, 2012, gabet123 said…

Your interaction number 2

At 11:21am on November 12, 2011, Unca RaF said…

Greetings,

   My name is Ralph Gugar from "North Coast Flow Testing Lab", and I'm also one of the founding members of the "International HHO Institute" (IHHOI). It has been brought to my attention through HHOINFO that you may have interest in having an HHO cell, flow tested. I'm sorry that someone from the IHHOI has not contacted previously, but there must be a glitch in the system from when someone requests info by clicking on the IHHOI link on HHOINFO.

   Please feel free to go directly to the IHHOI website at: "IHHOI.org" and you can learn exactly what the IHHOI is all about, from becoming a member, to HHO cell testing and how to place an order for a cell test, and to their vision of what they plan to accomplish:

  • To be the premier authority and open source of information for the
    discovery, development, and advancement of sustainable, renewable energy
    sources.
  • To promote HHO as a viable, sustainable, alternative energy.
  • To help reduce our dependence on foreign and domestic oil companies and our
    dependence on polluting, petroleum based-fossil fuels.
  • To provide standards for Quality, Safety, Installation, and Integrity
    solutions to meet the needs of its members.
  • Further, with the goal of becoming recognized as the “UL” for the HHO
    industry providing product registration and product performance certification.
 
 
 

*** Translate HODINFO ***

Latest Activity

Jediah Krajcik updated their profile
Thursday
Aaron Malczewski replied to DAN MERRICK's discussion 'hhhn vs hho'
Thursday
Wade Waters replied to Felix Audet's discussion 'Resonnance electrolysis VS HV flyback'
Wednesday
Jediah Krajcik is now a member of HODINFO
Aug 9
charles ware replied to charles ware's discussion 'Popular mechanics story on HHO'
Aug 2
Richard Keough updated their profile
Jul 31
Profile IconKiera and Clare Katz joined HODINFO
Jul 31
broandrew replied to charles ware's discussion 'Popular mechanics story on HHO'
Jul 30
Alan Smith replied to gabet123's discussion 'Harlo Mayne and Maynex'
Jul 25
gabet123 posted a discussion
Jul 25
gabet123 commented on David Brightman's status
Jul 24
Stuart Kinley joined James Morehead's group
Jul 23
David Brightman commented on David Brightman's status
Jul 22
gabet123 commented on David Brightman's status
Jul 22
David Brightman posted a status
". enough clearance between the electrodes as I cell I found a fine slurry of cast iron had bridged the regards Dave"
Jul 21
Heidi Dayne Hanson is now a member of HODINFO
Jul 17

© 2018   Created by gabet123.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

Live Chat