marc tamiso
  • Cabot, VT
  • United States
Share

Marc tamiso's Friends

  • Martin Moore
 

marc tamiso's Page

Latest Activity

marc tamiso replied to gabet123's discussion 'Howard Phillips Ace Cell'
"I see...bu what was the amp draw cold, then after it warmed up to CC temp? "
Dec 17, 2017
marc tamiso replied to gabet123's discussion 'Howard Phillips Ace Cell'
"Hi Jesse, thanks for your input- how much space is too much?   temperature is a huge factor, how are you dealing with insulating and protecting your electrolyte and water supply?  7 degrees below zero again last night, hope to make a…"
Dec 17, 2017
marc tamiso replied to gabet123's discussion 'Howard Phillips Ace Cell'
"Hi Allen, thanks, that's quite the generator.  Do you find hot spots on the electrodes or plates? I've found with hho cells the wider spacing increases voltage, but also circulation.  So, mild steel?  Please share wattage…"
Dec 17, 2017
marc tamiso replied to gabet123's discussion 'Howard Phillips Ace Cell'
"Hi Martin, that's great, very helpful...what is the advantage of 3mm spacing over a wider or variable spacing?  I've found with cast iron that the amperage draw was regulated by temperature and electrode weight (400+/- grams seems to…"
Dec 14, 2017
marc tamiso replied to gabet123's discussion 'Howard Phillips Ace Cell'
"by studding you mean spot welding?  Brazing would be my easy choice, but an alloy in electrolysis is problematic.  Will probably go with stainless, but he dislikes the poor electrical transfer of stainless, hence the mild steel tab. …"
Nov 20, 2017
marc tamiso replied to gabet123's discussion 'Howard Phillips Ace Cell'
"Hi all, so to pick up the conversation about attaching electrodes, the autopsy shows the soft solder is gradually failing, perhaps accounting for the diminishing gas output.  Also, this is brute force electrolysis, I assume pwm frequency will…"
Nov 20, 2017
marc tamiso replied to gabet123's discussion 'Catalytic Carbon PR11 Press Release new concepts and ACE cell.'
"In boatbuilding we say 'one size fits all fits no one well' or something like that...my point being that the power demands of hho cells that I'm using  (capacitive amperage limited  CAL ) give me ease of use,  and…"
Nov 14, 2017
marc tamiso replied to gabet123's discussion 'Catalytic Carbon PR11 Press Release new concepts and ACE cell.'
"Would you accept a well crafted sailboat, or a quality windmill or solar array as overunity? "
Nov 14, 2017
marc tamiso replied to gabet123's discussion 'Catalytic Carbon PR11 Press Release new concepts and ACE cell.'
"Hi Martin, just using acid core 50/50 plumbing solder, works faster and better for me than silver.  I've used the hho torch with soft and hard silver solder, but my best joints are with acid flux core solder. "
Nov 13, 2017
marc tamiso replied to gabet123's discussion 'Howard Phillips Ace Cell'
"Hi Jim, I' m using Howard's power supply design.  It's simple  to build ( although it took me a year) , but not as simple as Martin's, perhaps he has shared it here.  The weakness of a relay design is the relays,…"
Nov 13, 2017
marc tamiso replied to gabet123's discussion 'Catalytic Carbon PR11 Press Release new concepts and ACE cell.'
"Hi all, I've had great results soft soldering copper to cast iron with hho.  Electrodes need to be very clean. I' working with 1" pipe, quartered and stacked so there are 3 neutrals (to increase voltage).  I hope this…"
Nov 13, 2017

Profile Information

What is your HOD level of experience?
Intermediate Builder
What is your business contact info?
email to sovereign design vt
What do you do for a living or have special education in?
carpenter, boatbuilder, design work
Is there anything else you would like to add?
Actively working on ACE and ER_HHO. Contact me to talk hydrogen.
Current Status
Active builder

Comment Wall (1 comment)

You need to be a member of HODINFO to add comments!

Join HODINFO

At 6:21pm on November 11, 2017, Martin Moore said…

Is this that dodgy bloke from Oz?

I'll be travelling back to the UK Wednesday / Thursday next week so I'll get started on your module soon after I return.

I've got around 5 to make for next spring so yours will be first.

Martin

 
 
 

*** Translate HODINFO ***

© 2018   Created by gabet123.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

Live Chat